Futek CSG110 (JM-2A / JM-2AD)-Series Manuel d'utilisateur Page 1

Quick Start GuideSensor Solutions SourceLoad · Torque · Pressure · Multi-Axis · Calibration · Instruments · Softwarewww.futek.comCSG110Strain Gauge Un

101. The voltage output of the CSG110 is passed through a current converting phase. This means the prior Ex-citation and Gain setting steps of the vo

11SW5 SW6 SW7 Input Range Output Range▼ ▼ ▼0–10 V 4–20 mA▼ ▼ ▲0–10 V 5–25 mA▲ ▼ ▼0–10 V 0–16 mA▲ ▼ ▲0–10 V 0–20 mA▼ ▲ ▼0–5 V 4–20 mA▼ ▲ ▲0–5 V 5–25 mA

12DIP Switch 1: Excitation• The Excitation is the voltage supplied from the CSG110 to the sensor and can be 5 VDC or 10 VDC.• It is recommended to u

13DIP Switch 3: Sensitivity (Gain)• The Sensitivy DIP switch controls the gain needed to obtain the desired output level from the CSG110. For example

14DIP Switch 5, 6, and 7: Current Setting• The voltage output from the CSG110 is passed through a current conversion phase. As a result the current o

15Shunt is used to simulate a load on the sensor by using an internal resistor labeled ‘RSH’ on the CSG110 circuit board. The resistor will be connect

163 For FSH03546: Min. Power Supply is 12.5 VDC4 Only for sensitivity of 1 mV/V or greater5 Only for sensitivity of 1.5 mV/V or greaterVERSIONSITEM #

17SpecificationsENVIRONMENTPARAMETER MIN TYPICAL MAX UNITOperating Temperature32 158 °F0 70 °CStorage Temperature –40 185 °F–40 85 °CRelative Humidity

186 Minimum power supply varies for OEM models7 No load applied (input or output)ELECTRICAL SPECIFICATIONSPARAMETER MIN TYPICAL MAX UNITPower Supply61

19ELECTRICAL SPECIFICATIONS (CONTINUED)PARAMETER MIN TYPICAL MAX UNITNoise 15 mV p-pOutput Span Range –10 10 % of Rated OutputOutput Zero R

2Getting HelpJM-A2/D.12-13-0.0FUTEK reserves the right to modify its design and specifications without notice. Please visit http://www.futek.com/sales

20Related AccessoriesYELLOW MOLDED BOOT (INCLUDED) Item Number: FSH03219SHUNT RESISTORItem Number: Visit WebsiteSCREW TERMINAL (MALE)Item Number: FSH0

21To prevent damage, make sure all connections to the CSG110 are completed before turning on the power to the CSG110.It is best to troubleshoot the CS

22The CSG110 has no output or low, non-changing output.1. Confirm the power to the CSG110 is between 14 and 26 VDC.2. Confirm there is not a short

23Notes

10 Thomas, Irvine, CA 92618 USATel: (949) 465-0900Fax: (949) 465-0905www.futek.com

3Getting Help . . . . . . . . . . . . . . . . . . . . . . . 2Logic Board Configuration . . . . . . . . . . . . . . . . 4CSG110 Sensor Side Connections

4Logic Board ConfigurationExcitationPolarityGainCurrent SettingCurrent Input RangeCurrent SettingShuntSWSWSWSWSWSWSW1235678FEMALE MALE21 386 75

5CSG110 Sensor Side ConnectionsFEMALE DB9 SENSOR SIDEPIN # WIRING CODE1 + EXCITATION12 + SIGNAL 3 – SIGNAL 4 – EXCITATION1 5 GROUND6 GROUND7 GROUND8 G

6Sensor DB9 AssemblyMALE DB9 CONNECTOR (SUPPLIED)Top CoverNutsDB9 ScrewsCover ScrewsSet ScrewBottom CoverDB9 MaleWasher CoversInformation about your s

7CSG110 Power Side Connections1 2 3 4 56 7 8 92 Only available with current output option. Note: All grounds are connected together and pass through t

8Included Power Side DB9 Cable5 4 3 2 19 8 7 6FEMALE DB9 POWER SIDE (SUPPLIED)PIN # WIRING CODE CABLE COLOR CODE1 SIGNAL OUT (CURRENT) WHITE2 RETURN

91. Set SW 1 down for 10 VDC excitation or up for 5 VDC excitation. By default the CSG110 is set to 10 VDC at FUTEK.2. Set the gain DIP switch (SW3)