Futek IPM600 (D610) Digital Display Manuel d'utilisateur télécharger pdf (Page 105)

14.BCD DATA OUTPUT(OPTION)

Input

14-5. Signal Timing

This signal turns on at the same time as BCD data when stable.

OVER

This signal is outputted at the time of -ADC OVER, +ADC OVER, +overflow or -

overflow.

Vcc

F371

Inside

IC=Approx.6mA

COM

Switch

Transistor

+5V

TTL open collector output

󲃗

Open OFF

Short ON

NOTE

- Do not apply external voltage to the signal input circuit.

- The external element is required to withstand Ic=10mA.

- Leakage from the external element is required to be 30A or below.

Outside

BCDdata

P.C

OVER

1 2 ... 100 101 102 103 104 105 106 107 108 109 110 ... 135 136

IPM600 Series 1
Instruction Manual 1
Safety Precautions 3
WARNING 5
CONTENTS 10
1. APPEARANCE DESCRIPTION 12
1-2. Rear Panel 13
1-2-3. Optional Slot 15
2. SETTING MODES 16
2-2. Setting Modes Tree 17
2-3. About a Setting Call 19
3. CONNECTION 20
3-2. Load Cell Connection 21
3-3. SI/F Connection 22
3-4. External I/O Connection 23
4. CALIBRATION 27
4-3. Zero Calibration 30
4-4. Actual Load Calibration 31
4.CALIBRATION 33
4-6. Digital Offset 34
4-8. Decimal Place 36
4-9. Calibration Protection 37
4-11. Unit 40
5. SETTING OF FUNCTIONS 42
5-2. Digital Filter 43
5-3. Analog Filter 44
5-4. Display Rate 44
5-5. Stability 45
5-6. Zero Track 46
5-7. Contrast Adjustment 47
5-8. Backlight 47
5-9. Excitation Voltage 47
5-10. Auto Print 48
5-11. Hold Off Print 50
5-12. Parameter Protection 50
6. COMPARISON FUNCTIONS 51
6-2. Hysteresis 53
6-3. Near Zero 55
6-5. HI-LO Limit Output Mode 56
6-6. Alarm Mode 57
7. HOLD FUNCTIONS 58
7-1-2. Hold Detection Time 59
Simple setting call 59
7-1-3. Auto Start Level 60
7-1-4. Hold Point Shift 60
7-2-1. Minimum Count 62
7-2-2. Valley Detection Level 62
A 63
Data Section No 100
Terminator 101
Terminator 101
14. BCD DATA OUTPUT(OPTION) 103
14-4. Equivalent Circuit 104
14-2. Logic Change 104
14-3. BCD Data Hold 104
14-5. Signal Timing 105
How to set 106
15-2. RS-485 connection 107
Host Computer etc 108
Master Slave 108
15-3. Communication Method 110
16. D/A CONVERTER(OPTION) 112
16-2. D/A Output Mode 114
How to output adjust 115
17. DC POWER SOURCE 116
18. ERROR MESSAGES 117
19-1. Self-Check 118
Self-Check DSP 118
Self-Check MEM 118
Self-Check KEY 119
Self-Check EXT 119
19-3. Password 120
20. ABOUT JAPANESE/ENGLISH 121
DISPLAY SELECTION 121
21. BLOCK DIAGRAM 122
22. DIMENSIONS 123
23. INSTALLATION IN A PANEL 124
24. SPECIFICATIONS 125
24-3. Communication 126
24-4. Options 126
24-6. General 128
24-7. Accessories 129
25. SETTING ITEM CHART 130
Attachment of ferrite core 136

Commentaires sur ces manuels

Pas de commentaire

Futek IPM600 (D610) Digital Display Manuel d'utilisateur Page 105

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Futek IPM600 (D610) Digital Display