Futek IPM600 (D610) Digital Display Manuel d'utilisateur Page 5
- Page / 136
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS
This device complies with Part 15 of the FCC Rules. Operation is subject to
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested an found to comply with the limits for a
Class A Digital Device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable Protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
- - Reorient or relocate the receiving antenna.
- - Increase the separation between the equipment and receiver.
- - Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- - Consult the dealer or an experienced radio / TV technician for help.
WARNING
This equipment has been verified to comply with the limits for a Class A personal
digital device, pursuant to subpart B of Part 15 of FCC Rules. Only peripherals
(computer input / output devices, terminals, printers, etc.) certified or verified to
comply with the Class A or B limits may be attached to this equipment. Operation
with non-certified or non-verified personal computer and / or peripherals is likely to
result in interference to radio and TV reception. The connection of a non-shielded
equipment interface cable to this equipment will invalidate the FCC Certification of
this device and may cause interference levels which exceed the limits established
by the FCC for this equipment.
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.
- IPM600 Series 1
- Instruction Manual 1
- Safety Precautions 3
- WARNING 5
- CONTENTS 10
- 1. APPEARANCE DESCRIPTION 12
- 1-2. Rear Panel 13
- 1-2-3. Optional Slot 15
- 2. SETTING MODES 16
- 2-2. Setting Modes Tree 17
- 2-3. About a Setting Call 19
- 3. CONNECTION 20
- 3-2. Load Cell Connection 21
- 3-3. SI/F Connection 22
- 3-4. External I/O Connection 23
- 4. CALIBRATION 27
- 4-3. Zero Calibration 30
- 4-4. Actual Load Calibration 31
- 4.CALIBRATION 33
- 4-6. Digital Offset 34
- 4-8. Decimal Place 36
- 4-9. Calibration Protection 37
- 4-11. Unit 40
- 5. SETTING OF FUNCTIONS 42
- 5-2. Digital Filter 43
- 5-3. Analog Filter 44
- 5-4. Display Rate 44
- 5-5. Stability 45
- 5-6. Zero Track 46
- 5-7. Contrast Adjustment 47
- 5-8. Backlight 47
- 5-9. Excitation Voltage 47
- 5-10. Auto Print 48
- 5-11. Hold Off Print 50
- 5-12. Parameter Protection 50
- 6. COMPARISON FUNCTIONS 51
- 6-2. Hysteresis 53
- 6-3. Near Zero 55
- 6-5. HI-LO Limit Output Mode 56
- 6-6. Alarm Mode 57
- 7. HOLD FUNCTIONS 58
- 7-1-2. Hold Detection Time 59
- Simple setting call 59
- 7-1-3. Auto Start Level 60
- 7-1-4. Hold Point Shift 60
- 7-2-1. Minimum Count 62
- 7-2-2. Valley Detection Level 62
- A 63
- Data Section No 100
- Terminator 101
- Terminator 101
- 14. BCD DATA OUTPUT(OPTION) 103
- 14-4. Equivalent Circuit 104
- 14-2. Logic Change 104
- 14-3. BCD Data Hold 104
- 14-5. Signal Timing 105
- How to set 106
- 15-2. RS-485 connection 107
- Host Computer etc 108
- Master Slave 108
- 15-3. Communication Method 110
- 16. D/A CONVERTER(OPTION) 112
- 16-2. D/A Output Mode 114
- How to output adjust 115
- 17. DC POWER SOURCE 116
- 18. ERROR MESSAGES 117
- 19-1. Self-Check 118
- Self-Check DSP 118
- Self-Check MEM 118
- Self-Check KEY 119
- Self-Check EXT 119
- 19-3. Password 120
- 20. ABOUT JAPANESE/ENGLISH 121
- DISPLAY SELECTION 121
- 21. BLOCK DIAGRAM 122
- 22. DIMENSIONS 123
- 23. INSTALLATION IN A PANEL 124
- 24. SPECIFICATIONS 125
- 24-3. Communication 126
- 24-4. Options 126
- 24-6. General 128
- 24-7. Accessories 129
- 25. SETTING ITEM CHART 130
- Attachment of ferrite core 136
Produits connexes et manuels pour Capteurs Futek IPM600 (D610) Digital Display
(120 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.116 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels